Automate 410 Guía de instalación

© 1999 Directed Electronics, Inc. Vista, CA N410A 10-99Model 410Installation Guide®®

10 © 1999 Directed Electronics, Inc. Vista, CAConnect this wire to an ignition source. This input must show (+)12V with the key in run position and du

© 1999 Directed Electronics, Inc. Vista, CA 11When the system receives the transmitter code controlling Channel 2 for longer than 1.5 seconds, the RED

12 © 1999 Directed Electronics, Inc. Vista, CAharness 2 (H2), (+/-) door lock outputs__________________door lock wiring diagramsThis system can contro

© 1999 Directed Electronics, Inc. Vista, CA 13IMPORTANT! Remember that the functions of these wires reverse between Type A and Type B!This system is c

14 © 1999 Directed Electronics, Inc. Vista, CAInterfacing with a reversing polarity system requires either two relays or one 451M (not included). It i

© 1999 Directed Electronics, Inc. Vista, CA 15In order for this system to control one or more aftermarket actuators, a 451M or two relays (optional) a

16 © 1999 Directed Electronics, Inc. Vista, CADoor locks are controlled by an electrically activated vacuum pump. Some Mercedes and Audis use a Type D

© 1999 Directed Electronics, Inc. Vista, CA 17transmitter/receiver learn routine™Transmitters are taught to the system using the Learn Routine. This s

18 © 1999 Directed Electronics, Inc. Vista, CAYou can advance from one channel to another by releasing the Valet®/Program switch and tapping it to adv

© 1999 Directed Electronics, Inc. Vista, CA 19When programmed for single button arm/disarm configuration, the transmitter buttons are assigned as foll

2 © 1999 Directed Electronics, Inc. Vista, CAtable of contentsBitwriter™, Code Hopping™, DEI®, Doubleguard®, ESP™, FailSafe®, Ghost Switch™, Learn Rou

20 © 1999 Directed Electronics, Inc. Vista, CAoperating settings learn routine™Many of the operating settings of this unit are programmable. They can

© 1999 Directed Electronics, Inc. Vista, CA 21You can advance from feature to feature by pressing and releasing the Valet®/Program switch the number o

22 © 1999 Directed Electronics, Inc. Vista, CAfeature descriptions1 ACTIVE/PASSIVE ARMING: When active arming is selected, the system will only arm wh

© 1999 Directed Electronics, Inc. Vista, CA 23Disabling the Code Hopping™ feature lets the receiver ignore the Code Hopping™ part of the transmitted w

24 © 1999 Directed Electronics, Inc. Vista, CAtroubleshootingStarter kill does not work: Is the correct starter wire being interrupted? If the car st

© 1999 Directed Electronics, Inc. Vista, CA 3what is included The control module (see diagram) Two 476A remote transmitters The plug-in status LED

4 © 1999 Directed Electronics, Inc. Vista, CAinstallation points to rememberThis system has been designed to provide the ultimate in convenience to bo

© 1999 Directed Electronics, Inc. Vista, CA 5primary harness (H1), 12-pin connector___________________________________________________________________

6 © 1999 Directed Electronics, Inc. Vista, CAprimary harness (H1) wire connection guideThis wire supplies a (-) 500 mA ground as long as the system is

© 1999 Directed Electronics, Inc. Vista, CA 7IMPORTANT! Never use this wire to drive anything but a relay or a low-current input! The transis-torized

8 © 1999 Directed Electronics, Inc. Vista, CAType A (+) polarity system: Wire relays as shown.Type B (-) polarity system: Connect the BLUE H1/6 wire t

© 1999 Directed Electronics, Inc. Vista, CA 9Type C (+) reversing polarity system: Wire relays as shown.Connect this wire to bare metal, preferably wi